JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

Snap Out Tool for Pushbuttons - 24mm
The ultimate solution to easily disassemble your Sanwa / Seimitsu snap-on buttons.
   In stock  Buy Now
Snap Out Tool for Pushbuttons - 30mm
The ultimate solution to easily disassemble your Sanwa / Seimitsu snap-on buttons.
   In stock  Buy Now
Fuse holder for solenoid
Fuse holder cards are the essential complements to your solenoids.
With its diode, your solenoid will protect against voltage returns.
And, if the coil 'jams', the fuse will trip before melting your electrical installation.
   In stock  Buy Now
Solenoid 12V
11.40€
By placing 8 or 10 solenoids in your Pincab you will find these typical pinball noises.
Solenoids are one of the toys that polishes the realism of your pincab. The Freescale KLZ25 PCB and the Pinscape Config Tool software will allow you to control this solenoid.
Under Pinscape, in the Feedback Device Outputs, remember to activate the Flipper logic with 0% Hold power so that the reel does not remain blocked.
   In stock  Buy Now
Rubber coated balltop - Green
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Red
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Black
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Yellow
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Grey
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Blue
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
LED strip - 40cm with switch
Illuminate the marquee of your arcade machine or backlit the buttons on your panel with this LED strip.
   In stock  Buy Now
Cables for fighting board 2.8mm
Complete joystick / button wiring for Fighting Board PCB.
Connection to the 2x10 pin card support.
Standard connector for five-point joysticks (Sanwa Denshi, Seimitsu) and for buttons fitted with 2.8mm lugs.
   In stock  Buy Now
Wireless Fighting Board - Switch, PS3, PS4, PC
The Wireless Fighting Board from Brook will allow you to use your wireless arcade stick.
This multi console PCB (Switch, PS3, PS4, PC) without lag. It also offers X-Input and SOCD (Simultaneous Opposite Cardinal Direction) modes.
   In order  Buy Now
Flipper legs protectors - Pincab - Black (x4)
Set of four Polypropylene foot protections.
These protections help protect the body of your Pinball / Pincab from foot aggression.
These leg protectors slightly protrude from the feet of the Flipper / Pincab.
The protections are installed between the feet and the furniture.
   In stock  Buy Now
Flipper legs protectors - Pincab - Dark blue (x4)
Set of four Polypropylene foot protections.
These protections help protect the body of your Pinball / Pincab from foot aggression.
These leg protectors slightly protrude from the feet of the Flipper / Pincab.
The protections are installed between the feet and the furniture.
   In stock  Buy Now
Micro SD reader extension - 46 cm
Micro-SD reader extension.
Support all 16GB, 32GB, 64GB and 128GB Micro SD / SDHC cards.
N.B: The extension cable must be installed before switching on the product on which it is installed.
Product length: about 46 cm at each end (micro sd reader and male connector included).
   Low stock  Buy Now
Power cable jack 5.5mm Male multistandard 1m
5.5mm jack power cabling.
Connects to any electrical device using a 5.5 jack connector.
Its specific tip allows it to be installed on 5.5mm / 2.1mm or 5.5 / 2.5mm jack connectors.
Its length of one meter will allow you an easy installation
   In stock  Buy Now
Power supply 36V/10A - Terminals
36V / 10A terminal block power supply.
This power supply is used to supply several devices with 36V.
Ex: Audio amplifier for HP Body shaker
   In stock  Buy Now
Micro hdmi to hdmi adapter - Raspberry Pi4
Micro HDMI to HDMI adapter.
This adapter allows you to connect an HDMI-HDMI cable to one of the two micro HDMI ports of your Raspberry Pi4.
As the adapter is large, you will only be able to use one on your RaspBerry Pi4.
   In stock  Buy Now
Cable Jack 3.5mm stereo slim male - male 50cm
3.5 mm slim Male / Male AUDIO JACK cable for connecting audio devices with JACK plug.
This cable has gold-plated connectors.
Its small width allows it to be easily installed in a small space.
This cable is particularly suitable for our mini audio amplifiers which have a very thin jack connector.
   In stock  Buy Now