JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

Result Pages:
Snap Out Tool for Pushbuttons - 24mm
The ultimate solution to easily disassemble your Sanwa / Seimitsu snap-on buttons.
   In stock  Buy Now
Snap Out Tool for Pushbuttons
The ultimate solution to easily disassemble your Sanwa / Seimitsu snap-on buttons.
   In stock  Buy Now
Fuse holder for solenoid
Fuse holder cards are the essential complements to your solenoids.
With its diode, your solenoid will protect against voltage returns.
And, if the coil 'jams', the fuse will trip before melting your electrical installation.
   In stock  Buy Now
Solenoid 12V
9.90€
By placing 8 or 10 solenoids in your Pincab you will find these typical pinball noises.
Solenoids are one of the toys that polishes the realism of your pincab. The Freescale KLZ25 PCB and the Pinscape Config Tool software will allow you to control this solenoid.
   In stock  Buy Now
Rubber coated balltop - Green
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Red
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Black
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Yellow
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Grey
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Blue
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
LED strip - 40cm with switch
Illuminate the marquee of your arcade machine or backlit the buttons on your panel with this LED strip.
   In stock  Buy Now
Cables for fighting board 2.8mm
Complete joystick / button wiring for Fighting Board PCB.
Connection to the 2x10 pin card support.
Standard connector for five-point joysticks (Sanwa Denshi, Seimitsu) and for buttons fitted with 2.8mm lugs.
   In stock  Buy Now
Wireless Fighting Board - Switch, PS3, PS4, PC
The Wireless Fighting Board from Brook will allow you to use your wireless arcade stick.
This multi console PCB (Switch, PS3, PS4, PC) without lag. It also offers X-Input and SOCD (Simultaneous Opposite Cardinal Direction) modes.
   In stock  Buy Now
Flipper legs protectors - Pincab - Black (x4)
Set of four Polypropylene foot protections.
These protections help protect the body of your Pinball / Pincab from foot aggression.
These leg protectors slightly protrude from the feet of the Flipper / Pincab.
The protections are installed between the feet and the furniture.
   In stock  Buy Now
Flipper legs protectors - Pincab - Blue (x4)
Set of four Polypropylene foot protections.
These protections help protect the body of your Pinball / Pincab from foot aggression.
These leg protectors slightly protrude from the feet of the Flipper / Pincab.
The protections are installed between the feet and the furniture.
   In stock  Buy Now
NESPi 4 Case - Raspberry Pi 4
Give a retro look to your Raspberry Pi4 with this case which takes the design of the Nes.
It offers full access to the different elements of the RaspBerry: SD card, mini HDMI ports, audio jack connector, Ethernet port and power adapter.
The box also offers a removable cartridge in which you can install a 2.5 SSD hard drive (The hard drive must be an SSD).
   Low stock  Buy Now
Micro SD reader extension - 46 cm
Micro-SD reader extension.
Support all 16GB, 32GB, 64GB and 128GB Micro SD / SDHC cards.
N.B: The extension cable must be installed before switching on the product on which it is installed.
Product length: about 46 cm at each end (micro sd reader and male connector included).
   In stock  Buy Now
Micro SD reader extension - 15cm
Micro-SD reader extension.
Support all 16GB, 32GB, 64GB and 128GB Micro SD / SDHC cards.
N.B: The extension cable must be installed before switching on the product on which it is installed.
Product length: about 15cm at each end (micro sd reader and male connector included).
   In stock  Buy Now
Result Pages: