SmallCab
5.90 €
20% VAT incl.
20% VAT incl.
The USB to PSL 30N PCB is a board that can power up to 8 Seimitsu PSL-30N buttons.
By using the 5V contained in the USB connections, you can easily power your Seimitsu PSL-30-N buttons.
The card has a line of terminals for ground and a second line for +5V.
This card to be used in passthru of a USB controller card allows to recover the +5V/GND.
By using the 5V contained in the USB connections, you can easily power your Seimitsu PSL-30-N buttons.
The card has a line of terminals for ground and a second line for +5V.
This card to be used in passthru of a USB controller card allows to recover the +5V/GND.
20% VAT incl.
20% VAT incl.
To facilitate the installation of your DMDs on your Pincab, we offer you a DMD P2.5 pack ready to be installed.
This pack includes two DMD P2.5 panels installed on their frame, an STM32 PCB with its updated firmware and the Pin2DMD software installed (License not included and to be paid for).
This set will save you time when installing the DMD on your pincab.
The Pin2DMD software solution allows the reading of PAL/VNI and PAC files.
This pack includes two DMD P2.5 panels installed on their frame, an STM32 PCB with its updated firmware and the Pin2DMD software installed (License not included and to be paid for).
This set will save you time when installing the DMD on your pincab.
The Pin2DMD software solution allows the reading of PAL/VNI and PAC files.
20% VAT incl.
20% VAT incl.
To facilitate the installation of your DMDs on your Pincab, we offer you a DMD P3 pack ready to be installed.
This pack includes two DMD P3 panels installed on a frame / shield assembly and a Nucleo 144 PCB with its updated firmware and the Pin2DMD software installed (License not included and to be paid for).
This set will save you time when installing the DMD on your pincab.
The Pin2DMD software solution allows the reading of PAL/VNI and PAC files.
This pack includes two DMD P3 panels installed on a frame / shield assembly and a Nucleo 144 PCB with its updated firmware and the Pin2DMD software installed (License not included and to be paid for).
This set will save you time when installing the DMD on your pincab.
The Pin2DMD software solution allows the reading of PAL/VNI and PAC files.
21.90 €
20% VAT incl.
20% VAT incl.
The SmallCab PinToDMD Shield is a shield specifically designed for Nucleo 144 STM32F429zi / F439zi and for the PIN2DMD project (Virtual Pinball).
2.90 €
20% VAT incl.
20% VAT incl.
5.5mm jack power cabling.
Connects to any electrical device using a 5.5 jack connector.
Its specific tip allows it to be installed on 5.5mm / 2.1mm or 5.5 / 2.5mm jack connectors.
Its length of one meter will allow you an easy installation
Connects to any electrical device using a 5.5 jack connector.
Its specific tip allows it to be installed on 5.5mm / 2.1mm or 5.5 / 2.5mm jack connectors.
Its length of one meter will allow you an easy installation
3.90 €
20% VAT incl.
20% VAT incl.
5.5mm jack power cabling.
Connects to any electrical device using a 5.5 jack connector.
Its specific tip allows it to be installed on 5.5mm / 2.1mm or 5.5 / 2.5mm jack connectors.
Its length of one meter will allow you an easy installation
Connects to any electrical device using a 5.5 jack connector.
Its specific tip allows it to be installed on 5.5mm / 2.1mm or 5.5 / 2.5mm jack connectors.
Its length of one meter will allow you an easy installation
22.90 €
20% VAT incl.
20% VAT incl.
This ratchet wrench features a 5/8" head and a 9/16" second for use with all foot screws.
The 12-point bits allow easy access and grip of the foot screws, even in the tightest places.
This wrench is made from forged and heat-treated vanadium steel, allowing it to easily withstand daily use.
The 12-point bits allow easy access and grip of the foot screws, even in the tightest places.
This wrench is made from forged and heat-treated vanadium steel, allowing it to easily withstand daily use.
2.20 €
20% VAT incl.
20% VAT incl.
Round guide for Sanwa JLF-TP joystick.
This guide's role is to facilitate the creation of combos.
It also optimizes the movement of the stick from one direction to another.
This guide's role is to facilitate the creation of combos.
It also optimizes the movement of the stick from one direction to another.
14.90 €
20% VAT incl.
20% VAT incl.
The SC-Plunger pack is a simplified connection solution.
It consists of a linear stereo slide potentiometer, on which is soldered a PCB with six connectors.
Three connectors will connect the potentiometer to the KL25Z.
And, three additional connectors will allow you to connect up to three buttons.
It consists of a linear stereo slide potentiometer, on which is soldered a PCB with six connectors.
Three connectors will connect the potentiometer to the KL25Z.
And, three additional connectors will allow you to connect up to three buttons.
6 reviews
28.95 €
20% VAT incl.
20% VAT incl.
The handle of your arcade stick protrudes from your backpack when you travel?
SmallCab's 'Shaft QR' is the solution to this problem.
This new SANWA JLF-TP Joystick Removable Stick has been designed in two parts to help remove the top of the handle quickly and without hassle.it alos fit to your hori hayabusa joystick !
SmallCab's 'Shaft QR' is the solution to this problem.
This new SANWA JLF-TP Joystick Removable Stick has been designed in two parts to help remove the top of the handle quickly and without hassle.it alos fit to your hori hayabusa joystick !
28.95 €
20% VAT incl.
20% VAT incl.
The handle of your arcade stick exceed your backpack when you travel?
"The link" of PhreakMods is the solution to this problem.
This new rod was Seimitsu LS-32 joystick designed in two parts to allow removal of the top of the handle quickly and without hassle.
"The link" of PhreakMods is the solution to this problem.
This new rod was Seimitsu LS-32 joystick designed in two parts to allow removal of the top of the handle quickly and without hassle.
2.20 €
20% VAT incl.
20% VAT incl.
Sticker sheet for transparent or illuminated 28 / 30mm button.
Product to cut and stick on the patch which is inside the button.
Product to cut and stick on the patch which is inside the button.
24.95 €
20% VAT incl.
20% VAT incl.
The Shield KL25 - Plunger is a simplified connection solution for your Pincab project.
This shield will allow you to easily connect all the buttons you want as well as 8 PWM outputs and 8 digital outputs.
This shield will allow you to easily connect all the buttons you want as well as 8 PWM outputs and 8 digital outputs.
20% VAT incl.
20% VAT incl.
To make it easier for you to install your DMD panels on your Pincab, we offer a ZeDMD shield compatible with P2.5 and P3 panels.
Our offer consists of a shield (PCB) on which an ESP32 (Wroom32) card is installed with the ZeDMD software installed
This set will make it easier for you to install DMD tiles based on the ZeDMD software solution on your Pincab.
Our offer consists of a shield (PCB) on which an ESP32 (Wroom32) card is installed with the ZeDMD software installed
This set will make it easier for you to install DMD tiles based on the ZeDMD software solution on your Pincab.
35.90 €
20% VAT incl.
20% VAT incl.
Side rails for Flipper Bally / Williams, 2 pieces (left and right).
Rendered 'brushed' lengthwise.
Rendered 'brushed' lengthwise.
39.90 €
20% VAT incl.
20% VAT incl.
Side rails for Flipper Bally / Williams, 2 pieces (left and right).
Covered with black epoxy paint with 'textured' effect.
Covered with black epoxy paint with 'textured' effect.
33.90 €
20% VAT incl.
20% VAT incl.
Side rails for Bally / Williams pinball machine, 2 pieces (left and right).
Unprimed raw sheet metal, to be painted.
Unprimed raw sheet metal, to be painted.
14.90 €
20% VAT incl.
20% VAT incl.
Slotting Cutter Arbor.
Fits on any type of router.
This arbor is only compatible with Slotting Cutter for sale on this site.
Fits on any type of router.
This arbor is only compatible with Slotting Cutter for sale on this site.
2.90 €
20% VAT incl.
20% VAT incl.
This octagonal guide made by SmallCab is the essential complement to your SANWA JLF-TP joystick.
It facilitates the placement of directions and optimizes the distance the stick moves from one direction to another.
Thanks to this guide, you will easily make all the combos!
It facilitates the placement of directions and optimizes the distance the stick moves from one direction to another.
Thanks to this guide, you will easily make all the combos!
3.90 €
20% VAT incl.
20% VAT incl.
This long shaft for Seimitsu LS-32 joysticks is an anodised aluminum shaft 15mm taller than the original shaft.
This shaft was designed to allow the installation of a Seimitsu LS-32 joystick on a wood panel.
Sold out