JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

T-Molding 17.5mm (11/16") Chrome
Chrome T-molding 17.5mm (11/16") wide.
The price displayed is for a length of 1 meter.
   In stock  Buy Now
Molex converter to terminal blocks
This molex to terminal block converter will allow you to recover the 5V and 12V voltages from any molex connector of an ATX power supply.
The various voltages will be directly recoverable on the various terminal blocks provided for this purpose.
   In stock  Buy Now
Brook Wingman XBox adapter
The Wingman XB supports PS3 / PS4 / PS5 / Xbox 360 / Xbox One / Xbox Elite / Xbox Elite Series 2 controllers as well as arcade sticks to operate them on Xbox 360 / Xbox One or Xbox original.
   In order 
Ball Shooter Sleeve
Scabbard for williams type ball lance.
   Low stock  Buy Now
Shooter Assembly Flatwasher
Metal washer for williams type ball lance.
Williams ball launchers require two washers.
   In stock  Buy Now
White Shooter Tips
White rubber tip for williams type ball lance.
   In stock  Buy Now
Pack of 3 Williams ball lance mounting screws
This pack of three self-tapping screws will allow you to attach the ball lance to your Flipper or Pincab case.
   In stock  Buy Now
Pack 2 wing screws and 2 claw nuts - 8mm
This pack of two wing head screws and two claw nuts are intended to secure the pediment to the body of your mini Pincab.
   In stock  Buy Now
Pack 2 wing screws and 2 claw nuts - 6mm
This pack of two wing head screws and two claw nuts are intended to secure the pediment to the body of your mini Pincab.
   In stock  Buy Now
Pin2DMD - PCB STM32 NUCLEO 144 - F429ZI
The STM32 NUCLEO 144 - F429ZI PCB is the development board used by the V4 shields of the Pin2DMD team.
This card will ensure long-term support for the evolutions of the Pin2DMD software.
   In stock  Buy Now
Snap Out Tool for Pushbuttons - 24mm
The ultimate solution to easily disassemble your Sanwa / Seimitsu snap-on buttons.
   In stock  Buy Now
Snap Out Tool for Pushbuttons - 30mm
The ultimate solution to easily disassemble your Sanwa / Seimitsu snap-on buttons.
   In order  Buy Now
Fuse holder for solenoid
Fuse holder cards are the essential complements to your solenoids.
With its diode, your solenoid will protect against voltage returns.
And, if the coil 'jams', the fuse will trip before melting your electrical installation.
   In stock  Buy Now
Solenoid 12V
11.40€
By placing 8 or 10 solenoids in your Pincab you will find these typical pinball noises.
Solenoids are one of the toys that polishes the realism of your pincab. The Freescale KLZ25 PCB and the Pinscape Config Tool software will allow you to control this solenoid.
Under Pinscape, in the Feedback Device Outputs, remember to activate the Flipper logic with 0% Hold power so that the reel does not remain blocked.
   In stock  Buy Now
Rubber coated balltop - Green
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Red
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Black
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Yellow
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Grey
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now
Rubber coated balltop - Blue
KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).
   In stock  Buy Now