New Products
Seimitsu LS 5x/6x - Stock and hollow shaft
Seimitsu LS 5x / 6x hollow shaft for joysticks is a rod that can be used on a metal panel.
It has the characteristic of being hollow which makes it possible to pass light to a certain extent.
Concave dark gray short arcade button
Short and concave arcade button.
The concave shape of the button makes it ergonomic.
Its low height allows for easier installation in small spaces.
Professional quality, it will guarantee you thousands of hours of play.
Concave light gray short arcade button
Short and concave arcade button.
The concave shape of the button makes it ergonomic.
Its low height allows for easier installation in small spaces.
Professional quality, it will guarantee you thousands of hours of play.
Seimitsu LS 5x/6x - Short and hollow shaft
The short and hollow Seimitsu LS 5x / 6x joysticks rod is 6mm smaller than the original rods.
This rod can be used on a metal panel.
It has been designed to limit the movement of the stick by limiting the height between the handle and the panel.
It also has the characteristic of being hollow which makes it possible to pass light to a certain extent.
Seimitsu LS-32 - Pivot
Original Seimitsu LS-32 joystick pivot.
This pivot allows free movement of the joystick rod.
This part is based on the Seimitsu LS-32 base which is lubricated with grease to prevent premature wear.
Sanwa OBSF-24TR - Green
The SANWA OBSF-24TR button is a triangular button.
It is a button that can be clipped onto a metal panel with a rectangular base of 18mmx15mm.
Sanwa OBSF-24TR - Yellow
The SANWA OBSF-24TR button is a triangular button.
It is a button that can be clipped onto a metal panel with a rectangular base of 18mmx15mm.
Sanwa OBSF-24TR - Blue
The SANWA OBSF-24TR button is a triangular button.
It is a button that can be clipped onto a metal panel with a rectangular base of 18mmx15mm.
Sanwa OBSF-24TR - Red
The SANWA OBSF-24TR button is a triangular button.
It is a button that can be clipped onto a metal panel with a rectangular base of 18mmx15mm.
Button Blank 30mm
Button blank, allows simple plug a 30mm diameter hole of a button which is no longer used.
Deco Bartop 19 pouces - Arcade Monkey
Decoration for 19 "Smallart Bartop Kit.
Printed on an adhesive vinyl with glossy UV coating.
Deco Bartop 19 pouces - Arcade Goblins
Decoration for 19 "Smallart Bartop Kit.
Printed on an adhesive vinyl with glossy UV coating.
Deco Bartop 19 pouces - Arcade World
Decoration for 19 "Smallart Bartop Kit.
Printed on an adhesive vinyl with glossy UV coating.
Light dome with screw tabs
The Dome Flasher is a standard piece found on the playfield of a large number of pinball machines.
It can also be installed on the LEDbar of a pincab.
This dome flasher is installed with screws, you can equip it with star RGB LEDs to interact with your table.
Sold individually.
Terminal strip - 12 positions
Terminal block electrical connection block.
Can be used as a standard domino while having the advantage of being well fixed on a wooden support.
The twelve pairs of connections are isolated from each other.
Installs horizontally or vertically.
Attaches with two screws.
Extended Black Leg Bolt
Extended Black leg bolt for Pincab or Williams Flipper feet, Bally, Data East, Sega and Stern.
The screws are fixed on the foot cage (or inner nut plates).
Heavy Duty Leg Leveler w/Nut - Black
Black Heavy Duty Leg Leveler of Pincab or Flipper.
This leg leveler is equipped with a foot 4,5cm in diameter and a length of 7.3cm.
3.5V - 30V voltage booster
This 3V-30V Voltage Booster will allow you to use 24V devices from a 12V.
Only the voltage is adjustable, the amperage is not adjustable.