New Products

This pack of three self-tapping screws will allow you to attach the ball lance to your Flipper or Pincab case.

This pack of two wing head screws and two claw nuts are intended to secure the pediment to the body of your mini Pincab.

This pack of two wing head screws and two claw nuts are intended to secure the pediment to the body of your mini Pincab.

The STM32 NUCLEO 144 - F429ZI PCB is the development board used by the V4 shields of the Pin2DMD team.
This card will ensure long-term support for the development of the Pin2DMD software.

The ultimate solution to easily disassemble your Sanwa / Seimitsu snap-on buttons.

The ultimate solution to easily disassemble your Sanwa / Seimitsu snap-on buttons.

Fuse holder cards are the essential complements to your solenoids.
With its diode, your solenoid will protect against voltage returns.
And, if the coil 'jams', the fuse will trip before melting your electrical installation.

By placing 8 or 10 solenoids in your Pincab you will find these typical pinball noises.
Solenoids are one of the toys that polishes the realism of your pincab. The Freescale KLZ25 PCB and the Pinscape Config Tool software will allow you to control this solenoid.

KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).

KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).

KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).

KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).

KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).

KDIT offers us a new type of round handle with a 'silky' appearance.
With its 35mm diameter and 6mm thread, this handle is compatible with most joysticks on the market (Sanwa, Seimitsu, Hori and some Samducksa).

Illuminate the marquee of your arcade machine or backlit the buttons on your panel with this LED strip.

Complete joystick / button wiring for Fighting Board PCB.
Connection to the 2x10 pin card support.
Standard connector for five-point joysticks (Sanwa Denshi, Seimitsu) and for buttons fitted with 2.8mm lugs.

The Wireless Fighting Board from Brook will allow you to use your wireless arcade stick.
This multi console PCB (Switch, PS3, PS4, PC) without lag. It also offers X-Input and SOCD (Simultaneous Opposite Cardinal Direction) modes.

Set of four Polypropylene foot protections.
These protections help protect the body of your Pinball / Pincab from foot aggression.
These leg protectors slightly protrude from the feet of the Flipper / Pincab.
The protections are installed between the feet and the furniture.

Set of four Polypropylene foot protections.
These protections help protect the body of your Pinball / Pincab from foot aggression.
These leg protectors slightly protrude from the feet of the Flipper / Pincab.
The protections are installed between the feet and the furniture.

Give a retro look to your Raspberry Pi4 with this case which takes the design of the Nes.
It offers full access to the different elements of the RaspBerry: SD card, mini HDMI ports, audio jack connector, Ethernet port and power adapter.
The box also offers a removable cartridge in which you can install a 2.5 SSD hard drive (The hard drive must be an SSD).