JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

Short shaft for magnetic joystick
This short rod has been designed in collaboration with Industrias Lorenzo to transform a 'magnetic' pear joystick into a magnetic joystick with handle.
   In stock  Buy Now
Long shaft for magnetic joystick
This long stem has been designed in collaboration with Industrias Lorenzo to transform a 'Magnetic' pear joystick into a handle joystick.
   In stock  Buy Now
Shin-Etsu silicone grease tube 100gr
Sanwa and Seimitsu joysticks use silicone grease to lubricate the joystick pivot.
This allows for smooth movement during gameplay.
All joysticks come with a small amount of grease already applied, but this may wear off over time.
   Low stock  Buy Now
Set of 20 pink Bubbletop handles
Set of 20 pink "bubble" transparent ball grips for Zippy/Sanwa/Seimitsu joystick.
The bubbles are not homogeneous from one handle to another.
   In stock  Buy Now
Set of 20 blue Bubbletop handles
Set of 20 blue "bubble" transparent ball grips for Zippy/Sanwa/Seimitsu joystick.
The bubbles are not homogeneous from one handle to another.
   In stock  Buy Now
Bumper flipper
64.90€
The Bumpers or 'mushrooms' are most often three in number and placed at the very top of the playfield.
The pinball ball goes from bumper to bumper making as much noise as possible.
This is an element that contributes to the sensations restored by your Pincab to make it as close as possible to a real pinball machine.
The Bumpers are controlled with a Freescale KLZ25 PCB, a mosfet card and the Pinscape Config Tool software.
   In stock  Buy Now
Guide Sanwa GTN-VI
The GTN-VI insert is an insert for GT-8X guide.
Developed by Sanwa, it optimizes the JLF series joysticks, with more precise guides in the directions.

The Sanwa GTN-VI insert is a round guide that allows 360 degree freedom of movement.
To use it, you must have the Sanwa GT-8X support.
   In stock  Buy Now
Guide Sanwa GTN-Y
The GTN-Y insert is an insert for GT-8X guide.
Developed by Sanwa, it optimizes the JLF series joysticks, with more precise guides in the directions.

The Sanwa GTN-Y insert is a guide that facilitates 360° movements, with marked angles.
To use it, you must have the Sanwa GT-8X support.
   In stock  Buy Now
Guide Sanwa GTN-B
The GTN-B insert is an insert for GT-8X guide.
Developed by Sanwa, it optimizes the JLF series joysticks, with more precise guides in the directions.

The Sanwa GTN-B insert is a guide with a unique shape, rounded above and below, with marked angles on the right and left.
To use it, you must have the Sanwa GT-8X support.
   In stock  Buy Now
Guide Sanwa GTN-R
The GTN-R insert is an insert for GT-8X guide.
Developed by Sanwa, it optimizes the JLF series joysticks, with more precise guides in the directions.

The Sanwa GTN-R insert is a square guide with rounded corners.
To use it, you must have the Sanwa GT-8X support.
   In stock  Buy Now
Guide Sanwa GT-8X -  4/8 way
This 4/8 way guide (GT-8X) is an original part for SANWA joystick from the JLF-TP range.
This guide is essential for the installation of the GTN-VI, GTN-Y, GTN-R, GTN-B guides.
The central part is removable and has two positions (4 or 8 ways).
By default, the guide is delivered in the 8-way position.
   In stock  Buy Now
Complete slingshot type Stern
The slingshot is the component that pushes the ball back when you come into contact with the rubber band of the island placed above the flippers.
It is an element that contributes to the sensations returned by your Pincab to make it as close as possible.
The Knocker is controlled with a Freescale KLZ25 PCB and the Pinscape Config Tool software.
   In stock  Buy Now
Sanwa JLF-SP-VI Spring - Violet (Tension 1, 1.5)
The JLF-SP-VI spring is taken from the official Sanwa kit to optimize the JLF series joysticks.
It allows you to adjust the stiffness of the rod, both at the start and at the end of the race (see detail in the diagram).

The table shows the forces exerted by the different springs at two times of the stroke of the rod.
For the violet spring, the tension is 1 times that of the original spring, when the handle is in position 1.
And, the tension is 1.5 times that of the original spring when the handle is in position 2.
   In stock  Buy Now
Sanwa JLF-SP-Y Spring - Yellow (Tension 1.3, 2)
The JLF-SP-Y spring is taken from the official Sanwa kit to optimize the JLF series joysticks.
It allows you to adjust the stiffness of the rod, both at the start and at the end of the race (see detail in the diagram).

The table shows the forces exerted by the different springs at two times of the stroke of the rod.
For the yellow spring, the tension is 1.3 times that of the original spring, when the handle is in position 1.
And, the tension is 2 times that of the original spring when the handle is in position 2.
   In stock  Buy Now
Sanwa JLF-SP-R Spring - Red (Tension 2, 2)
The JLF-SP-R spring is taken from the official Sanwa kit to optimize the JLF series joysticks.
It allows you to adjust the stiffness of the rod, both at the start and at the end of the race (see detail in the diagram).

The table shows the forces exerted by the different springs at two times of the stroke of the rod.
For the red spring, the tension is 2 times that of the original spring, when the handle is in position 1.
And, the tension is 2 times that of the original spring when the handle is in position 2.
   In stock  Buy Now
Sanwa JLF-SP-B Spring - Blue (Tension 1.5, 1.5)
The JLF-SP-B spring is taken from the official Sanwa kit to optimize the JLF series joysticks.
It allows you to adjust the stiffness of the rod, both at the start and at the end of the race (see detail in the diagram).

The table shows the forces exerted by the different springs at two times of the stroke of the rod.
For the blue spring, the tension is 1.5 times that of the original spring, when the handle is in position 1.
And, the tension is 1.5 times that of the original spring when the handle is in position 2.
   In stock  Buy Now
Sanwa JLF-P-B - Actuator
The JLF P-R is an actuator produced by Sanwa to optimize its JLF series joysticks.
This actuator offers a shorter engagement distance.
   In stock  Buy Now
Sanwa JLF-P-R - Actuator
The JLF P-R is an actuator produced by Sanwa to optimize its JLF series joysticks.
This actuator offers a shorter engagement distance.
   In stock  Buy Now
Ball Top red - Sanwa LB-35-NR Nylon
The surface of this ball top is treated with nylon material which has a felt-like texture.

This results in a very particular touch comparable to that of velvet.
   In stock  Buy Now
Ball Top blue - Sanwa LB-35-NB Nylon
The surface of this ball top is treated with nylon material which has a felt-like texture.

This results in a very particular touch comparable to that of velvet.
   In stock  Buy Now